View and Download Kurzweil PC3 musician’s manual online. Kurzweil PC3: User Guide. PC3 Electronic Keyboard pdf manual download. Also for: Pc3x. View and Download Kurzweil PC3x service manual online. PC3x Synthesizer pdf manual download. Kurzweil®, and PC3® are trademarks of Young Chang Co., Ltd. All other products and brand names are trademarks or registered trademarks of their respective.
|Published (Last):||4 August 2010|
|PDF File Size:||9.57 Mb|
|ePub File Size:||1.52 Mb|
|Price:||Free* [*Free Regsitration Required]|
The bottom edge of the rear panel and back edge of the bottom enclosure connect to form a lip. Unlock the key from the pivot anchoring the key to the keyboard chassis. PC3 or higher 2. Page an example This test is safe to run on an xD Card that has data on it. Enter text from picture: The expected test result when the Alpha Wheel is turned is one of four values—0, 1, 2, or 3: Tilt the unit up and install the four enclosure support wall screws.
Page 75 assigned to However, to avoid reversing the Bass and Treble cables when reconnecting, mark one or both cables designating B for Bass and T for Treble. Important Safety Instructions Read these instructions. Slide the left side of the unit forward off of your work surface so that you can access the four screws and washers securing the assembly to the bottom enclosure.
Many, but not all, PC3 sample roots have been pre-assigned a carefully chosen, fixed alternate sample start or end point that can be selected using the Alternate Switch feature altControl and altMethod parameters.
This cable is bundled with other cables routed along the rear panel portion of khrzweil top enclosure. However, the maximum size for xD cards formatted on the PC3x is Mb. Connect the stranded wire cable from the Wheels Assembly to J To print the manual completely, please, download it.
Tilt the PC3x up and install the six keyboard rear screws. Install the 18 screws that secure the board to the keyboard chassis. Install the four screws that secure it to the front panel bezel. Follow the procedure described on page to remove the Connector Board. These screws also secure kurzwei, rear panel edge of the Board. Follow the procedure described on page to remove the enclosure support wall. Refer to Figure on page Audio Output If the diagnostic version is 0.
Kurzweil PC3 Musician’s Manual
Page What module do you want to update? Position the Bass Contact Board on the keyboard chassis. Chapter 2 Diagnostics The following lists the diagnostic tests available for the PC3x. Don’t have an account? Slide the PC3x forward so that you can install the six keyboard front screws. See Chapter 3, Page Clean only with dry cloth.
Page 76 The PC3 contains both stereo and mono samples Keymaps designed for stereo use are labeled with names beginning with “Stereo” or ending in “Left,” “Right,” “L,” and “R.
Page 6 Removing the Wheels Assembly If you are replacing the Front Panel Board with another board, be sure to remove the four screws that secure the LCD bezel to the board and install it on the new board. Add to my manuals Add. Move the PC3x back onto your work surface.
Manua, to Kurzdeil Chapter 1 Introduction This chapter provides the service technician with a layout of the front and rear panel features, as well as a brief explanation of their functions.
Kurzweil Music Systems – PC3X – PC3 Series Musician’s Guide
The Mannual should boot up normally. What module do you want to update? Lift off the clip. For instructions, refer to the Boot Loader in Chapter 4, page An example of the expected test results for the pitch wheel follows your results may vary slightly: Page 23 Diagnostics Description of Tests Notes 1.
Pressing these buttons simultaneously, selects the Jump function. If you use 5 mm X 20 mm fuses, install them toward the inside end of the fuse holder near the metal pins. Front Panel Problems 4. Page 58 System objects installed. Kurzweil Music Systems S. Enter text from picture: PC3x bottom enclosure Caution: Note Start the sample will begin at the pre-set alternate start point in this case, slightly past the initial chiff.
LCD lit, no characters 1. Do not remove the endcap or rear panel screws at this point of the procedure. By pressing ‘print’ button you will print only current page. If possible, save all user programs and setups before disassembly.