Icharger B Pdf User Manuals. View online or download Icharger B User Manual. Read online or download PDF • Page 4 / 33 • ProgressiveRC B iCharger User Manual • ProgressiveRC Power suppliers. My iCharger B was one of the earliest released so it has firmware version where as current models are shipping with version
|Published (Last):||23 August 2018|
|PDF File Size:||2.14 Mb|
|ePub File Size:||20.71 Mb|
|Price:||Free* [*Free Regsitration Required]|
iCharger B+, B+, B, B, B and B – RC Groups
When you turn on the charger you are usually in a selection in one of the right four columns of the map shown below. Files View all Files in thread.
Lithium packs of cells can be charged in balanced or unbalanced mode. It is a simple process: This can ichagger very useful if you are trying to “zoom” in on an area of the graph.
ProgressiveRC 208B iCharger User Manual
Of course there is shipping to consider. The pricing is pretty sharp if it is for single units rather ichadger a carton full and the chargers can live up to their specifications. Input leads, output leads, balance port adapters, temperature probe, PC interface and software etc? Therefore I offer two quick start examples in order to demonstrate a typical usage. 20b8 following lists are their main specifications: See detail information about logview in the following website: Basically any cell combination of most any rechargeable chemistry with a termination voltage of 36 volts or less can be charged.
With the exception of the low indication of power and temperature these results are very good.
Icharger B Manuals
Similarly, LiFe A packs of cells can be charged in balance mode or cells in unbalanced mode. Where and when can those be purchased? The first example assumes that the last battery charged was not a LiPo and none of the charge parameters are correct and they will all need changed.
Originally Posted by ozace Looks and sounds like.
Once you’ve had a few moments to practice icharegr it is really pretty simple to understand and get around. Upgrading steps posted by Julez! A typical result is shown in the table below. However, the B does not require the use of the balance tap ichargger can charge the full 20A in unbalanced mode which is no better than the chargers of old.
Last edited by kgfly; Apr 01, at Looks and sounds like. Pressing “Inc” will cycle through the cell voltages while pressing “Dec” will cycle through all the other items listed.
You can plot data from the B as it operates if plugged in via the USB cable or you can download saved data from the B flash memory. These suggestions and bug reports have been accepted with amazing open mindedness by the manufacturer, including adding the foam cutting feature as suggested by one of the forum members. I have seen a laptop get fried by current through the ground wire of a USB cable so this is not an unnecessary ichatger.
Connect Li batteries’ balance port 3. Some don’t like how easy it is to bump this button and accidentally terminate the charge, but mnual a safety standpoint it is refreshingly icharter and easy.
Connect the main charging port’s positive pole to cells’ positive pole, and then connect negative pole to cells’ negative pole this will avoid striking fire while connecting Li cells. You’ll want to become familiar with the differences between the various LiPo charge modes as there are no less than 8 variations. All measurements were performed using a charge scenario chosen to minimize that rate of change of the parameter being measured.
One complaint I have is that if you have button beeps turned off you won’t get a beep acknowledging the cancel so you have to go off of the data displayed on the screen to verify that the charger halted the charge.
Another reason they caught my eye was their thread on RCGroups where they listen to customer feedback and use the feedback to fix bugs and add features. But once you start to connect an 8S LiPo to your charger you may be startled by the loud pop and spark that result. There is table of error messages in the back of the user manual, but as often the case the error displayed on the screen and its description in the manual might mean little to the end user.
Mabual have also included a few measurements from my Watt’s Up meter as a point of comparison. DC power input cables and USB connector. If the balance tap is required to be connected then the balancer is active while in the other manula the balancer is not active and connecting the balance tap simply allows you to monitor cell voltages.
Do not charge a battery unattended Do not charge near flammable objects Do not exceed the rated cell voltage for your ambient temperature typically 4. This is the drawback of having a generic plotting utility that does not know how the data is associated with each other.
Between the output banana jacks and the balance port connector is a 3 pin connector for the temperature probe. The voltage range for cells are all shown and they can be scaled individually or as a group. Ciharger Quick Reply – Please Wait.