CU320 MANUAL PDF

SINAMICS S Equipment Manual for Booksize Power. Units. • SINAMICS S Equipment Manual for Description of the LED states of a CU SINAMICS S Equipment Manual for Booksize Power Units .. CU DP from firmware version with integrated Ethernet interface. ○ Smart Line. Siemens SINAMICS S Manual Online: Control Unit (cu), Description, Safety Information. Control Unit (CU) Description The CU

Author: Grogal Zolojinn
Country: Kosovo
Language: English (Spanish)
Genre: Career
Published (Last): 11 April 2011
Pages: 291
PDF File Size: 1.86 Mb
ePub File Size: 17.23 Mb
ISBN: 925-9-36930-346-2
Downloads: 66898
Price: Free* [*Free Regsitration Required]
Uploader: Zulkigal

LG CU320 Manuals

Control De Desplazam The control cables must be connected in accordance with the interface assignment and the shield applied. Internal air cooling In this standard solution, the power loss from the electronics and power units of the drive components is removed by natural cooling or by a forced-ventilation system and routed to the interior of the control cabinet. Where can should I go for support, replacement or repairs? Modules and components should only be stored and transported in conductive packaging such as metalized plastic boxes or metal containers.

DANGER When establishing connections to the manuak voltage busbar system, you must ensure that you do not mix up the power supplies. The table below shows the content of this accessories kit and the fixing points for connecting the cabinet units. CU and BOP20 2. Du320 jumpers of the DC busbar must always be connected in busbar systems. The measurements may only be carried out by properly trained specialist personnel.

Hacer Una Llamada The selected project is displayed at the top left. For example, the operation of pacemakers can be impaired, potentially leading to damage to a person’s health or even death.

  HAULOTTE HA20PX PDF

Darn, there are no reviews yet for this phone.

Use cable ties to secure the cable at suitable points. Function test with no motor connected Unit acceptance in presence of customer: The notes on the packaging relating to transportation, storage, and proper handling must be observed.

Figure Setting terminals for the fan transformers to V 2 AC Figure Setting terminals for the fan transformers to V 2 AC The line-voltage assignments for making the appropriate setting on the fan transformer are indicated in the following table.

Main setpoint [CDS] Sets the signal source for speed setpoint 1 of the speed controller 0 Interconnecting to r on its own drive object DO 63 Effect: Special attention should be paid to cable dimensioning, fuses, grounding, shutdown, disconnection, and overcurrent protection.

Loosen the single M12 nut of the PE busbar on the first cabinet. All of the approvals, certificates, declarations of conformity, test certificates, e.

The mabual 50 Nm must uc320 observed to manyal excessive heating of the terminal contacts during operation.

Deselect function 0 signal: Side panel installed on the right option M26? Procedure, see Subsection 3. Make sure that personnel are wearing the appropriate protective gear. Answering An Incoming Call Prices Where to Buy.

Its factory settings ensure that the required voltages can be fed to the relevant areas of the cabinet from the busbar. Note Check the boxes accordingly in the right-hand column if the activity applies to the cabinet unit in your scope of delivery. Active Line Modules draw a virtually sinusoidal current from the supply system and cause virtually no line harmonic distortions.

The handle must be mounted for option L37 DC interface including pre-charging input circuit. If you do have to touch modules, your body must be electrically discharged first.

  BRUCE TRIGGER HISTORIA DEL PENSAMIENTO ARQUEOLOGICO PDF

The open connections that are correspondingly marked must be wired up according to the circuit diagram.

Siemens SINAMICS S120 Manual: Control Unit 320 (cu320); Description; Safety Information

One jumper connects one busbar system. Table 4- 15 Checklist for cabling or connection work for Motor Modules in chassis format Completed?

Measuring sockets j 2 mm C320 Meas. Ensure that the ground at the installation location is strong enough to bear the weight of the cabinet units. You must read the safety information and application notes.

Are all of the prerequisites for commissioning checked and were the points in the checklist for commissioning checked refer to Chapter 2? Fasten the signal cables at suitable points.

Cingular mall, Shop tones, Shop games | LG CU User Manual | Page 57 / 99

The cooling air supply and exhaust must not be obstructed and must be available in sufficient quantity. Be the first to write a review. You must read and comply with the safety information provided in this manual.

Automatic optimization is a simple way of optimizing the control response. Since variance cannot be precluded entirely, we cannot guarantee full consistency. The front panel where the connections are located and the ,anual of the components are common to all designs.

Fecha Y Hora The auxiliary voltage busbar system is equipped with Faston terminals. Terminar Una Llamada De Conferencia Re-tighten the nuts on the DC busbar in both cabinet units torque: Electronic rating plates ensure automatic and error-free preconfiguration of the drive system.