CPM2A MANUAL PDF

Refer to the CPM1/CPM1A/CPM2A/CPM2C/SRM1(-V2) Programming Manual ( W) for details on programming opera- tions. CPM2C Features and. Part number. Operation manual. CPM2A operation manual. W Programming manual. CPM1/CPM1A/CPM2A/CPM2C/SRM1(-V2) Programming Manual. All OMRON products are capitalized in this manual. The word “Unit” is also capitalized when it refers to an OMRON product, regardless of whether or not it.

Author: Tumi Mezilrajas
Country: Belgium
Language: English (Spanish)
Genre: Literature
Published (Last): 24 July 2004
Pages: 279
PDF File Size: 6.53 Mb
ePub File Size: 4.18 Mb
ISBN: 174-1-86364-454-8
Downloads: 90812
Price: Free* [*Free Regsitration Required]
Uploader: Mibei

Page Programming Console, —, buzzer operation, Programming Console, 99 data link, 6, 86 date. Appendix B Dimensions All dimensions are in millimeters. When connecting the PC to a personal computer or other peripheral device, ei- ther ground the 0-V side of the PC or do not ground the PC at all. Page 17 Incorrect tightening torque may cp,2a in malfunction. Output Indicators The output indicators are lit when the corresponding output terminal is ON. Buzzer Manua, Before inputting a new program, any error messages recorded in memory should be cleared.

Lift the terminal block off the CPU Unit.

The status of the displayed words can be changed at this point. Page 20 Cpma2 Directives Countermeasure Examples When switching an inductive load, connect a surge protector, diodes, etc.

The following examples show how to input a new SV constant and how to change the SV from a constant to an address. Is the ambient Consider using a temperature above heater.

Page 46 Before using manua CPM1A program containing one or more of the instructions in the table above, check the program to be sure that it will operate properly and edit the program cpm22a necessary. Do not connect bare stranded wires directly to terminals. Not turning OFF the power supply may result in malfunction or electric shock.

  BUSHCRAFT 101 DAVE CANTERBURY PDF

The key functions for these Pro- gramming Consoles are identical. Install surge protec- tors or other noise- Is noise being reducing equipment controlled? Are the terminal screws loose?

Page Tighten screws or Are there any loose terminal screws or bro- replace wires. Section 5 describes how to perform a test run and how to diagnose and correct the hardware and soft- ware errors that mmanual occur during PC operation. Fatal Errors Unit configuration.

Setup and set the RSC port communications mode to 1: See clock decimal data with sign. Lift up the lock lever. Section 4 describes how to connect the Programming Console, and how to perform the various program- ming operations. Not connecting to the maunal ground may result in electric shock.

This section provides mannual precautions for using the Programmable Controller PC and related devices. Press and hold the Shift Key to input a letter shown in the upper-left corner of the key or the upper function of a key that has two functions. Input Indicators The input indicators are lit when the corresponding input terminal is ON. Correct the short circuit or limit Has the external the connected load to the spec- power supply shorted ification range.

Terminal screw size Power interrupt janual AC power supply: Not doing so may result in mal- function or damage. Note Refer to Programming Errors for details on check levels and the errors that may be detected when the program is checked.

Confirm that no adverse effects will occur to the system before downloading. Circuit Cp2a Characteristic Required element CR method If the load is a relay or solenoid, there The capacitance of the capacitor must be 1 to 0. Clearing Memory Completely 5. Fork terminal Ring terminal 6. Page 84 IN through IN have different values.

  AZ1117 DATASHEET PDF

OMRON CPM2A – 11-2005 Manual

Page 99 Do not connect bare stranded wires directly to terminals. Page numbers refer to the previous version.

Page Output signal ranges: ON see note Pin 7: If no errors are found, the following display will appear. If the Programming Console is connected to the PC when PC power is already on, the first display below will indicate the mode the PC was in before the Pro- gramming Console was connected. A 1 indicates a bit is on, and a 0 indicates it is off. Output Short Protection The output janual internal circuitry might be damaged when the load connected to an output is short-circuited, so it is recommended to install a protective fuse in each The SV must thus be set to 0.

Before using a CPM1A program containing one or more of the instructions in the table above, check the manjal to be sure that it will operate properly and edit the program if necessary.

OMRON CPM2A – MANUAL Pdf Download.

Peripheral Port The peripheral port must be vpm2a to the default communications settings shown Communications below. Then enter the correct input. The cursor will move one bit to the right after one of these keys is pressed. Straighten the pins on the EEPROM, line up with the socket and lower into the socket, as shown in the following diagram.