ASTM F2329 PDF

Zinc Coating Thickness Requirements: ASTM A vs. F Dimension. ASTM A ASTM F Avg. Coating. Thickness of. Specimens. Tested. ASTM F covers the requirements for hot-dip zinc coating applied to carbon steel and alloy steel bolts, screws, washers, nuts, and special. ASTM A does not cover threaded bolts and fasteners. ASTM A and F are the ASTM specifications that cover the requirements for.

Author: Gardagrel Mezil
Country: Iran
Language: English (Spanish)
Genre: Environment
Published (Last): 9 April 2011
Pages: 304
PDF File Size: 19.12 Mb
ePub File Size: 15.59 Mb
ISBN: 555-7-69587-914-5
Downloads: 13160
Price: Free* [*Free Regsitration Required]
Uploader: Yotilar

Zinc Coating Thickness Requirements: The number of specimens to be tested per order shall be as speci? Materials and Manufacture 5.

Hot-Dip Galvanizing Specifications – Portland Bolt

For test method, see Best practice is to note the bath temperature when galvanizing steel to F, although only the average bath temperature is required. The temperatures used in the hot-dip galvanizing process typically do not appreciably alter the mechanical properties of steel, but there are some instances when there are potential concerns.

If you are concerned about the hardness dropping, you could look at alternatives platings that do not require heat, like mechanical galvanizing. Workmanship, Finish, and Appearance 9. Otherwise, a third party will be required to apply the lubricant at an additional cost.

They shall then conform to f3229 requirements of this speci? Chemical Composition of Zinc 6. ASTM A This specification covers the requirements for hot-dip galvanizing on iron and steel products made from rolled pressed and forged shapes, castings, plates, bars, and strips.

  ASTM D4065 PDF

This ASTM specification covers zinc coatings applied by the hot-dip process on iron and steel hardware. There are three columns listing the number of test articles for three different inspection tests required under F Current edition approved Feb. Beams and structural members are defined as steel products and are galvanized per A Baking shall be conducted after pickling and prior to hot-dip galvanizing.

ASTM F2329 vs. ASTM A153

F defines the two different lots and their associated sampling plans as follows:. In addition, the purchaser shall provide fasteners having sufficient dimensional allowance to accommodate the zinc thickness deposition, as required in 8.

The differences in the types of lots entail different sampling plans, which specify the number of test articles for performing various test methods during inspection of the finished product.

NOTE 2—Hot-dip washers tend to bond to each other. Therefore, it must be clarified whether the plant has the ability to lubricate hardware after hot-dip galvanizing. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

Smoothness of a surface is a relative term. For each of these types, there are also inspection criteria for coating thickness, visual appearance, and adhesion.

Fasteners and nuts over 3? Also, A and F have different sampling requirements; F requires more samples per lot than A In no case shall the average of the measurements be below the average thickness shown in the Average Thickness on Individual Specimen column see These requirements are established by the applicable product standard, such as Speci?

  COMUNICACION ESCRITA HECTOR PEREZ GRAJALES PDF

Nails and rivets are not included in F April 10, Authored by Bernardo A. Vinay- ASTM A and A both say that the maximum service temperature for galvanized bolts should not exceed F unless caution is used in regard to the potential for liquid hydrogen embirittlement.

ASTM F – Portland Bolt

On the other hand, if embrittlement testing is necessary under F, it is to be conducted per ASTM F a wedge positioned and tensioned under a bolt headwhich is a different method than any of the methods described within A Paragraph 9.

This specification covers the requirements for hot-dip galvanizing on iron and steel products made from rolled pressed and forged astn, castings, plates, bars, and strips.

Nails and rivets are not included in this speci?

A touches on threaded fasteners, but is not fastener specific. Also a high tension rod U Bolt 14mm diameter and 2 meters in length also with its respective fasteners. NOTE 1—The scope of this speci?