This standard is issued under the fixed designation D ; the number immediately This test method was adopted as a joint ASTM–IP standard in operator prepares and inserts the beakers (with test oil, covers, and stirrers) into the bath as per ASTM D method. The test rod assembly (includes the steel. Model is a 6 test positions agitated liquid bath conforming to ASTM D, D, D, NACE TM and other similar tests. A timer alerts the.
|Published (Last):||11 February 2007|
|PDF File Size:||11.65 Mb|
|ePub File Size:||19.78 Mb|
|Price:||Free* [*Free Regsitration Required]|
This test method was used as a basis for Test Method D Clear plastic stirrers’ shield for 6 position baths. C0 Standards Related Products 1. Referenced Documents purchase separately D6665 documents listed below are referenced within the subject standard but are not provided as part of the standard. Provision is made in the procedure for testing heavier-than-water fluids.
Rust Preventing Characteristics Oil Bath – Koehler Instrument Company, Inc.
dd665 It consists of a motor rotating the chuck at to rpm. Home Products Contacts Search. The test beakers rest on a perforated support rack at the test specified level. This test method is also used for testing hydraulic and circulating oils, including heavier-than-water fluids.
FTM Paddle and Shaft. Holding chuck for polishing test specimen. Model A is an aluminum dry bath with 4 positions. Individual stirrers have the ability to be lifted out of the test beaker by simply loosening the knurled holding nut and lifting from the beaker. The stainless asym bath has drain for easy replacement of the bath medium.
In addition, a float switch interrupts power to the heaters in the event of low bath liquid level. Silicone carbide paper grit 50 sheets. Ashm advantage of the these aluminum baths over a liquid bath is the safety with the elimination of fumes and fire hazards if using oil as the bath medium.
Clear plastic stirrers’ shield for 4 position baths. A digital tachometer is provided displaying the rotational speed of the stirrers. Specifications subject to change without notice.
Rust-Preventing Characteristics of Mineral Oil – ASTM D665, D3603, D7548 | NACE TM-01-72 | IP 135
A protective cover is provided over the motor. Polishing device with e665 Volts. This test method is also used for testing other oils, such as hydraulic oils and circulating oils.
Work Item s – proposed revisions of this standard. The individual stirrers are belt driven. Note 1—For synthetic fluids, such as phosphate ester types, the plastic holder and beaker cover should be made of a chemically resistant material, such as polytetrafluoroethylene PTFE. It is used d65 specification of new oils and monitoring of in-service oils.
ASTM D Rusting Characteristics of Petroleum Products
C0 Standards Related Products. Model is identical to Model but with only 4 test positions. When lifted, the stirrer shaft protrudes through the top of the apparatus, allowing full and easy access to the test beaker. Work Item s – proposed revisions of this standard. No other units of measurement are adtm in this standard. Active view current version of standard. A secondary high temperature limit switch prevents over heating in the event of primary controller failure. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Beaker cover for D and D, each. Each position is individually temperature controlled and independent of other positions. The design chuck is as specified by the test method. Historical Version s – view previous versions of standard. Rusting test apparatus assembly with specimens for D Fig. Provision is made in the procedure for testing heavier-than-water fluids. Link to Active This link will always route to the current Active version of the standard.
Test Method D is used to test the oil on separate horizontal and vertical test rod surfaces, and can provide a more asmt evaluation. This standard does not purport to address all of the safety concerns, if any, associated with its use.
Models A and B are identical to Models A and B, respectively, but with 6 test positions. Horizontal disc test specimen for D, each.