ASTM D MEK Test (Zinc Test) – Free download as PDF File .pdf), Text File . txt) or read online for free. Designation: D – Standard Test Method for. Measuring MEK Resistance of Ethyl Silicate (Inorganic) Zinc-Rich Primers by Solvent Rub1 This standard. Designation: D – 03 Standard Test Method for Measuring MEK Resistance of Ethyl Silicate (Inorganic) Zinc-Rich Primers by Solvent Rub1.
|Published (Last):||17 July 2015|
|PDF File Size:||4.53 Mb|
|ePub File Size:||15.13 Mb|
|Price:||Free* [*Free Regsitration Required]|
If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Complete each double rub one forward and back motion in about 1 s. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
Using the procedure outlines in this test method, eight different operators were asked to rate, in triplicate, the methyl ethyl ketone R4752 rub resistance of a particular inorganic zinc-rich primer.
The primer was separately applied to multiple test panels at two different dry? Historical Version s – view previous versions of standard.
Link to Active This link will always route to the current Active version of the standard. Rate the results in accordance with Table 1.
Solvent Resistance Rub Test – ASTM D4752
The MEK resistance of some two-component ethyl silicate zinc-rich primers has been shown to correlate well with the cure of the primer as determined by diffuse reflectance infrared spectroscopy. Users of this standard are expressly advised that d4725 of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. It has been shown that the degree of axtm of ethyl silicate zinc-rich primers can c4752 measured by the chemical changes occurring using diffuse re?
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Practice D is the preferred method for organic coatings. Practice D is the preferred method for organic coatings.
Last previous edition approved in as D — Performance ratings and general statistical information have been in Table X1.
Current edition approved Jan. Reagents and Materials 5. Specific hazard statements are given in Section 6.
The values given in parentheses are for information only. Individual reprints single or d44752 copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. As relative humidity and temperature vary during the day, so does the rate of cure. A number in parentheses indicates the year of last reapproval.
If the former, record the number of rubs when the substrate is exposed.
Use this area as the control to visually show the appearance of No Effect. Sstm values given in parentheses are for information only. Clean the surface with tap water or dry cloth to remove loose material. Do not allow more than 10 s to elapse before proceeding to the next steps.
Originally approved in The following observations were made through this analysis: A certain minimum degree of cure is necessary prior to topcoating.
The MEK resistance of some twocomponent ethyl silicate zinc-rich primers has been shown to correlate well with the cure of the primer as determined by diffuse re? It has d47552 shown that the degree of cure of ethyl silicate zinc-rich primers can be measured by the chemical changes occurring using diffuse reflectance infrared spectroscopy.
Precision qstm Bias 8. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Mark a by mm 6- by 1-in. TABLE 1 Scale for Resistance Rating Resistance Rating 5 4 3 2 1 0 Description No effect on surface; no zinc on cloth after 50 double rubs Burnished appearance in rubbed area; slight amount of zinc on cloth after 50 double rubs Some marring and apparent depression d4572 the?
A superscript epsilon e indicates an editorial change since the last revision or reapproval. The Society for Protective Coatings, 40 24th St. Separate test panels corresponding to each coating thickness category were scored after a 6-h cure period and a h cure period. As relative humidity and temperature vary during the day, so does the rate of cure.
A certain minimum degree of cure is necessary prior to topcoating. Referenced F4752 purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.