Metal Type. UNS N Bar. ASTM B AMS Din Wire. Sheet. ASTM B AMS Din Plate. ASTM B AMS Din VAT (Alloy / ASTM B / UNS N) Nickel Alloy As it is corrosion resistant in oxidizing and reducing conditions, this alloy is virtually free of. ASTM Standards: 3. B Specification for Nickel-Chromium-Iron Alloys 1 This specification is under the jurisdiction of ASTM Committee B02 on.
|Published (Last):||19 March 2010|
|PDF File Size:||5.67 Mb|
|ePub File Size:||19.91 Mb|
|Price:||Free* [*Free Regsitration Required]|
Current edition aatm March 15, Hot-worked material to be machined in longer lengths should be speci? A Dimensions apply to diameter of rods, to distance between parallel surfaces of hexagons and squares, and separately to width and thickness of rectangles. If two choices are possible, as when the digits dropped are exactly a 5, or a 5 followed only by zeros, choose the one ending in an even digit, with zero de?
Cold-worked annealed or hot-worked All products, all sizes Hot-worked Annealed: The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not asym standard. NOTE 1—In order that the hardness determinations may be asgm reasonably close agreement, the following procedure is suggested as follows: Inconel exhibits cold forming characteristics normally associated with chromium-nickel stainless steels. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
Special End Uses S1. For each multiple, an allowance of 1? C Hardness B75 to B95, or equivalent. This standard is subject to revision zstm any time by the responsible technical committee and must be reviewed every? Cold-worked annealed or hot-worked All products, all sizes Forging Quality: The nickel content gives it excellent resistance to chloride-ion stress-corrosion cracking and also provides excellent resistance to alkaline solutions.
Request quote on this grade. Your comments are bb166 either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.
The wire shall withstand the wrapping test without fracture or development of a pebbled or orange-peel surface. Astmm is the responsibility of the user of this standard to become familiar with all hazards including those identi?
Inconel 600 (UNS N06600) Ni 76.0, Cr 15.5, Fe 8.0 Description
Longitudinal strip specimens shall be prepared in accordance with Test Methods E 8 for rectangular bar up to 1? Individual reprints single or multiple copies asgm this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.
This abstract is a brief 1b66 of the referenced standard. E Rods and bars, all sizes Forging Quality: Except as otherwise speci? Rejection should be reported to the producer or supplier promptly and in writing. Workmanship, Finish, and Appearance 8.
If you feel that your comments have not b1166 a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Cold-worked wire shall not be out-of-round by more than one-half the total permissible variations in diameter shown in Table 6.
Alloy N remainderA Examples of such requirements include, but are not limited to, the following: Inconel is a nickel-chromium alloy designed for use from cryogenic to elevated temperatures in the range of deg F deg C. ASTM Sstm takes no position respecting astn validity of any patent rights asserted in connection with any item mentioned in this standard. The material shall conform to the composition limits specified in a reference material.
This standard does not purport to address all of the safety concerns, if any, associated with its use. The alloy resists steam and mixtures of steam, air and carbon dioxide.
No mechanical properties are required. The material shall be uniform in quality and condition, smooth, commercially straight or flat, and free of injurious imperfections. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM B (INCONEL)_百度文库
Machining Type Suggested starting rates are: B — 08 Standard Speci? All sizes UNS N Type C-3 for finishing. Mechanical properties of the alloys like tensile strength, yield strength, elongation, and hardness shall be determined by tension and hardness tests. B Spot grinding is permitted to remove minor surface imperfections. Approved March 15, Bar, wire cuts, sheet, plate, strip, tube, pipe.