ASTM A – Designation: A – 10 Standard Speci?cation for Stainless Steel Bars and Shapes1 T. This standard is issued under the fixed designation A ; the 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel. ASTM Aa. November 1, Standard Specification for Stainless Steel Bars and Shapes. This specification covers hot-finished or cold-finished bars .
|Published (Last):||22 September 2016|
|PDF File Size:||17.7 Mb|
|ePub File Size:||2.91 Mb|
|Price:||Free* [*Free Regsitration Required]|
The free-machining types Note 2 for generalcorrosion resistance and high-temperature service are covered in aseparate specification. G Product analysis tolerance over the maximum limit for carbon and nitrogen shall be 0. Individual reprints single or multiple copies of this standard a2766-13a be obtained by contacting ASTM at the above address or at phonefaxor service astm.
The values given in parentheses aremathematical conversions to SI units that are provided forinformation only and are not considered standard. D The material shall be capable of meeting the required reduction of area where listed, but actual measurement and reporting of the reduction of area are not required unless speci? Failure to comply with the general requirements of Speci?
Note 1—For barsfor reforging, see Specification A If you feel that your comments have not received a fair hearing asm should make your views known to the ASTM Committee on Standards, at the address shown below. Condition A in which the bars are annealed Condition H in which the bars are hardened and tempered at a relative temperature Condition T in which the bars are hardened and tempered at a relatively high temperature Condition S in which the bars are strain hardened or aetm light cold worked Condition B in which the bars are relatively severe cold worked.
Originally approved in E Or equivalent Rockwell hardness. Current edition approved May 1, A number in parentheses indicates the year of last reapproval.
ASTM A276 Specification
It includes rounds, squares, and hexagons, and hot-rolled or extruded shapes, such as angles, tees, and channels in the more commonly used types of stainless steels.
NOTE 4—A typical ordering description is as follows: Such requirements may include but are not limited to the following: Monitoring Standards monitoring is a free service designed for you who wish to be alerted of changes to or new editions of the standards required in your work.
Condition A in which the bars are annealed, Condition H in which the bars are hardened and tempered at a relative temperature, Condition T in which the bars are hardened and tempered at a relatively high temperature, Condition S in which the bars are strain hardened or relatively light cold worked, and Condition B in which the bars are relatively severe cold worked.
D Nitrogen content is to be reported for this grade. It includes rounds, squares, and hexagons, and hot-rolled or extruded shapes, such as angles, tees, and channels in the more commonly used types of stainless steels.
The material shall be subjected to a mechanical test to determine its tensile strength, yield strength, elongation, and Brinell hardness.
ASTM specification – Stainless Steel Bars & Structurals | Penn Stainless Products
You need to log in before adding standards to the monitoring service. Users of this standard are expressly advised that determination of the validity of any such patent w276-13a, and the risk of infringement of such rights, are entirely their own responsibility. This standard has been approved for use by agencies of the Department of Defense.
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
B For some speci? A web subscription provides an easy and secure access to standards, and you are guaranteed to always have the latest edition. Read more about subscriptions. More specifically, the ASTM specification encompasses the following products in the more commonly used types of stainless steel:. Webprint Printed and bound. This service a2766-13a not available if you are a URL user where you do not log in with an email a267-13a.
Including alloyed steels, corrosion-resistant steels, heat-resisting steels, etc.
F Nickel plus copper shall be 0. The ASTM A specification covers hot -finished or cold-finished stainless steel bars, except bars for reforging.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? In such cases, the purchaser should so indicate on the order. adtm
astm a round bar, astm a rounds, astm a hex bar, astm a rod
Subscription – always available and updated A web subscription provides an easy and secure access to standards, and you are guaranteed to always have the latest edition. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
The use of sub-size test specimens, when necessary, is permissible in accordance with Test Methods and De? Take advantage of our other mill depot stocking locations in: C For some applications, the substitution of Type L for Typeor Type L for Type may be undesirable because of design, fabrication, or service requirements.
Our main stainless inventory and processing center is located in Quakertown, PA. A T T Hhot-? The bars shall be furnished in one of the following conditions: This ensures that you are always up-to-date and saves you both time and money. The bars shall be furnished in one of the following conditions: Last previous edition approved in as A — 08a. NOTE 3—There are standards covering high nickel, chromium, austenitic corrosion, and heat resisting alloy materials.
The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.