View and Download ABB ACS user manual online. ACS Inverter pdf manual download. MTAC pulse encoder interface module user’s manual 3AFE MUL1- R1 installation instructions for ACS, ACS,. ACS, ACS and. ACS Drives Users Manual ACS Three Phase Input. ABB ACS general machinery drives are designed for the OEM machine building sector.
|Published (Last):||27 February 2016|
|PDF File Size:||19.20 Mb|
|ePub File Size:||2.65 Mb|
|Price:||Free* [*Free Regsitration Required]|
Derivative action boosts the controller output if the error value changes. Dimensions Dimensional drawings of the ACS are shown below. Page 50 Set the deceleration time 1 parameter Example The time scheme below visualises the operation of the sleep function.
Installation mwnual commissioning flowchart Task Identify the frame size of your drive: Parameter Mode Parameter mode In the Parameter mode, you can: To print the manual completely, please, download it. Battery A battery is only used in Assistant Control Panels that have the clock function available and enabled. Ce Marking Applicable standards The drive complies with the following standards: Output mode In the Output mode, you can: Example 2 Example 2: Motor Cable Shield Motor cable shield To function as a protective conductor, the shield must have the same cross-sectional area as the phase conductors when they are made of the same metal.
Table Of Contents Parameters — complete descriptions Page 82 How to upload and download parameters For the manal and download functions available, see above. Fieldbus interface as the source for inverted Run Enable signal Run Disablei. UL marking See the type designation label for the valid markings of your drive.
Mark the locations for the holes using e. During the delay the drive knows accurately the rotor position. The resistance of the sensor increases sharply as the motor temperature rises over the PTC reference temperature Trefas does the voltage over the resistor.
ABB ACS350 User Manual
Determine the required maximum braking power P for the application. Rising edge maunal inverted digital input DI1: If the measured tension exceeds the tension setpoint, the speed will be slightly decreased, manhal vice versa. Enter text from picture: The Fieldbus Control Interface The fieldbus control interface The communication between a fieldbus system and the drive consists of bit input and output data words with ABB Drives profile and bit input and output words with DCU profile.
Using the information given in this chapter most alarm and fault causes can be identified and corrected. The drive cannot supply the motor with a voltage greater than units the amnual power voltage. Page Actual signals and parameters Control Of A Mechanical Brake Control of a mechanical brake The mechanical brake is used for holding the motor and driven machinery at zero speed when the drive is stopped, or not powered.
Alarm limit and fault trip limit. Save the new setting by pressing If you want to monitor actual values during the ID Run, go to the Output mode by pressing repeatedly until you get there. With Pt the output current is 9. Fieldbus network Fieldbus adapter Drive Industry standard drive profile e. mxnual
ABB ACS USER MANUAL Pdf Download.
Speed control performance figures The table below shows typical performance figures for speed control. Underload Protection Loss of motor load may indicate a process malfunction. The integration time defines the rate at which the controller output changes when the error value is constant. Motor Potentiometer macro This macro provides a cost-effective interface for PLCs that vary maanual speed of the drive using only digital signals.
To do other tasks, go first to the Main menu and select acz350 appropriate mode on the menu. However, it might be useful at this stage to set the parameters required by your application and save the settings as a user macro as instructed in section Definition of motor set-up data.
Safety What this chapter contains The chapter contains the safety instructions which mmanual must follow acd350 installing, operating and servicing the drive. System overview The drive can be connected to an external control system via a fieldbus adapter or embedded fieldbus.
A fan has vibrations in the range of 18 to 23 Hz and 46 to 52 Hz. Control panel cable In remote use, the cable connecting the control panel to the drive must not exceed 3 m 10 ft.
Unfiltered signal Filtered signal Time constant 0. See section Speed compensated stop on page Ratings on page Plan the installation: Direction change zcs350 locked. Page An alarm or fault message on the panel display indicates abnormal drive status. This function allows the highest possible switching frequency at manuaal specific operation point. Parameter Backup Mode Parameter Backup mode The Parameter Backup mode is used to export parameters from one drive to another or to make a backup of the drive parameters.
The construction of frame sizes R0…R4 varies to some extent.